US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1 Manual do Utilizador Página 60
- Página / 158
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
USRobotics
Command Reference
Data Command Set - 52
<orig_fbk> Decimal number which specifies the acceptable fallback mode of
operation when the modem is operating as the originator.
0 LAPM, MNP, or Normal Mode error control optional. (Default.)
1 LAPM, MNP, or Direct Mode error control optional.
2 LAPM or MNP error control required; disconnect if error control is
not established.
3 LAPM error control required; disconnect if error control is not
established.
4 MNP error control required; disconnect if error control is not
established.
<ans_fbk> Decimal number which specifies the acceptable fallback mode of
operation when the modem is operating as the answerer or
specifies V.80 Synchronous Access Mode.
1 Error control disabled, use Normal Mode.
2 LAPM, MNP, or Normal Mode error control optional. (Default.)
3 LAPM, MNP, or Direct Mode error control optional.
4 LAPM or MNP error control required; disconnect if error control is
not established.
5 LAPM error control required; disconnect if error control is not
established.
6 MNP error control required; disconnect if error control is not
established.
8 Initiate V.80 Synchronous Access Mode when connection is
completed, and Data State is entered (see +ESA and +ITF
commands).
Examples
+ES=6 Enable V.80 Synchronous Access Mode originator
+ES=,,8 Enable V.80 Synchronous Access Mode answerer
+ES=6,,8 Enable V.80 Synchronous Access Mode originator and answerer
+ES=3 Enable V.42 with Detection Phase originator. Disable V.80
Synchronous Access Mode originator.
+ES=,,2 Allow LAPM, MNP, or Normal Mode connection answerer.
Disable V.80 Synchronous Access Mode answerer.
- USRobotics Controllerless 1
- Command Reference 1
- Contents 3
- Introduction 9
- USRobotics 10
- Syntax and Procedures 11
- Command Line Editing 12
- Command Line Echo 12
- Repeating a Command Line 12
- Types of DTE Commands 12
- Basic Syntax Commands 13
- Extended Syntax Commands 14
- Action Commands 16
- Parameter Commands 17
- Issuing Commands 18
- Executing Commands 19
- Modem Responses 20
- Extended Syntax Result Codes 21
- Syntax and Procedures - 14 22
- Data Command Set 25
- Data Command Set - 18 26
- Result Code 29
- Data Command Set - 23 31
- DTE-Modem interface Commands 33
- Data Command Set - 26 34
- Data Command Set - 28 36
- Table 3-1: Result Codes 38
- Data Command Set - 32 40
- Data Command Set - 34 42
- Data Command Set - 37 45
- Syntax 47
- Data Command Set - 42 50
- Data Command Set - 44 52
- Modulation Control Commands 54
- Data Command Set - 47 55
- +MCR: Report Syntax 58
- +MRR: Report Syntax 58
- Error Control Commands 59
- Data Command Set - 54 62
- Data Command Set - 56 64
- Data Command Set - 59 67
- Data Command Set - 61 69
- V.8/V.8bis Commands 70
- Data Command Set - 63 71
- Data Command Set - 65 73
- Diagnostic and Test Commands 76
- Command Syntax 77
- Data Command Set - 70 78
- Data Command Set - 72 80
- Value Description Notes 82
- Data Command Set - 75 83
- Data Command Set - 77 85
- %TT5xyz 87
- Data Command Set - 80 88
- Data Command Set - 82 90
- Response 92
- Data Command Set - 85 93
- Data Command Set - 87 95
- Example: -QCPS: (0,1) 97
- S-Parameters 99
- Factory Defaults 100
- S-Parameter Definitions 101
- S-Parameters - 94 102
- S-Parameters - 96 104
- S-Parameters - 98 106
- Code Message Meaning 108
- Fax I/O Processing 115
- Fax Origination 117
- Fax Answering 117
- Fax Control Transmission 117
- Fax Control Reception 118
- Fax Data Transmission 119
- Commands and Parameters 120
- Mode Commands 121
- Defined Values 122
- Result Codes 122
- Write Syntax 127
- Typical Response 131
- Examples 133
- Voice Commands 135
- Voice Commands - 128 136
- Voice Commands - 135 143
- Voice Commands - 137 145
- Voice Commands - 139 147
- Voice Commands - 141 149
- Example: 150
- Voice Commands - 143 151
- Voice Commands - 145 153
- +VSP - Speakerphone ON/OFF 155
- Voice Commands - 148 156
Manuais e produtos relacionados com Modems US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1
(20 páginas)
(30 páginas)
(44 páginas)
(80 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais